Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

航天嵌入式软件数组越界缺陷特征研究

根据统计,数组越界是航天嵌入式软件开发过程中出现最多且最容易被遗漏的缺陷类型之一.目前自动化检测数组越界多基于抽象解释、符号执行、程序模型检验等方法,这些方法在误报、漏报、可扩展性等方面的表现依赖于软件及缺陷特征.分析了近三年航天嵌入式软件第三方测试中发现的94个数组越界问题,从缺陷模式和缺陷表现形式两方面分析得出10项航天嵌入式软件数组越界缺陷特征,并提出对设计具体检测方法关键的若干启示.进一步基于这些特征和启示探讨了数组越界检测算法针对中断驱动型程序的改进方向.     

星载激光通信终端在轨机动对温度影响

对激光通信终端在轨瞬态温度变化开展了仿真，以期研究在轨机动的影响、热分析和热试验时机动模式的简化模拟。通过合理地分析与简化，建立终端的轨道热分析模型，准确模拟在轨机动，根据典型机动模式、外热流和涂层退化等因素设计了计算工况，得出了终端在轨运行过程中的温度场随时间和姿态变化规律。结果表明：不同机动模式下的温度变化存在差异，最大可达23.0℃，采用固定姿态或一维转动的简化热分析或热试验不能准确模拟实际飞行温度，甚至不能部分替代二维转动热分析或热试验；光学天线和反射镜的温度控制是制约终端工作的瓶颈，为终端设计合适的避光机动策略，可大幅度提高温度稳定度和均匀度。研究结果可以为光机电设备在轨机动策略的设计和改进提供参考。     

Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

Accurate approximation of in-ecliptic trajectories for E-sail with constant pitch angle

Propellantless continuous-thrust propulsion systems, such as electric solar wind sails, may be successfully used for new space missions, especially those requiring high-energy orbit transfers. When the mass-to-thrust ratio is sufficiently large, the spacecraft trajectory is characterized by long flight times with a number of revolutions around the Sun. The corresponding mission analysis, especially when addressed within an optimal context, requires a significant amount of simulation effort. Analytical trajectories are therefore useful aids in a preliminary phase of mission design, even though exact solution are very difficult to obtain. The aim of this paper is to present an accurate, analytical, approximation of the spacecraft trajectory generated by an electric solar wind sail with a constant pitch angle, using the latest mathematical model of the thrust vector. Assuming a heliocentric circular parking orbit and a two-dimensional scenario, the simulation results show that the proposed equations are able to accurately describe the actual spacecraft trajectory for a long time interval when the propulsive acceleration magnitude is sufficiently small.     

基于梯度提升决策树的量子科学实验卫星光学实验预测

量子科学实验卫星在轨运行期间完成4种光学实验，地面监测人员通过遥测参数阈值判断卫星是否进行光学实验、实验类型及实验结果.这种方法需要预先设定大量阈值，并且这些阈值需要根据在轨卫星重新设定，可扩展性较差.针对以上问题，提出一种基于机器学习的光学实验判别方法，将量子科学实验卫星的光学实验监测任务抽象为机器学习中的多元分类问题，构建分类模型，利用量子科学实验卫星的真实历史遥测数据对模型进行训练，并通过真实实验计划对训练得到的模型进行验证.实验结果表明，本文提出的方法在没有专家先验知识的前提下，判别准确率达到99%，可用于量子科学实验卫星光学实验的实时监测任务.提出的基于机器学习的判别方法具有较强的可扩展性，可应用于卫星在轨运行的其他监测任务.      

某型装备能源电池异常爆破故障分析

对一起因电池设计缺陷引发装备战训失利的故障进行分析,重点对电池工作机理和设计缺陷展开解析,明确故障定位,并对国内外装备弹上不同体系电池的优缺点进行比较,旨在为产品维护保障、国产化科研等工作提供参考。     

某机载探测系统自主回收技术的实现

针对某机载探测系统探头回收自动化程度低的问题，提出了在无需操作员干预情况下实现探头自主回收的技术方法。采用了先进的控制算法，将缆位角与探头、缆长进行结合并引入了绞车控制系统，使绞车对探头的回收速度及缆长可进行实时调整，并给出了3种不同缆位角摆动条件下缆长与探头回收速度的控制曲线关系。研发了自主回收装置，设计了能够实现自主回收功能的探头回收机构。实验验证表明：在无需人为干预的条件下，在缆位控制系统及自主回收机构的配合下，系统实现了对探头快速、安全的回收。     

天基轻气炮发射清除低轨碎片方案及关键技术分析

文章分析了现有的空间碎片清除方式,并以800~1200 km低地球轨道高度上1~10 cm量级的空间碎片为清除目标,提出了天基轻气炮清除碎片的新方法。首先分析了轻气炮有效载荷在典型参数下的弹丸加速能力;之后根据将碎片降轨使其坠入大气层烧毁的设想,提出天基轻气炮共面清除碎片的方式,并选择轨道高度800 km的圆轨道作为碎片运行轨道进行可行性分析。计算表明,对半径10 cm、厚度1 cm的铝合金圆板碎片(质量211.95 g),使用初速1 km/s、重10 g的黏性弹丸可按任务方案达到清除效果。此外,计算出该参数弹丸对轨道高度800~1200 km的圆轨道上可清除的最大碎片质量为500~825 g,证明轻气炮弹丸对1~10 cm的碎片具有较强的清除能力。最后,分析了以轻气炮为有效载荷的航天器在完成清除碎片任务时的关键技术。